Loading
ГлавнаяБлогиСтатья №33192

Making A Miniature Photo Frame

goldfriesgoldfries6 месяцев назадTutorial
I'd like to take this opportunity to share about HOW to make a photo frame for your miniatures, the photo frame is as seen in my photo here PICTURE #1759718

Yup, it's real. I didn't post-process (add via software) like how I did last time. This is actual work.

http://www.moeness.com/wp-content/uploads/2017/05/photoframe_01.jpg

For this project I used thin low density wood for the frame as they are easy to handle, you can even cut them with a scissor.

Before you begin, you should have the image printed so you are able to estimate the size of the frame. Once you completed the estimation, cut them accordingly.

Do consider increasing the brightness of the photo before print


http://www.moeness.com/wp-content/uploads/2017/05/photoframe_02.jpg

Getting the framet in place is quite tricky. I used strong glue
to get the job done.

Just make sure the frame is as close to a rectangle (or square, or whichever
shape you intend it to be).


http://www.moeness.com/wp-content/uploads/2017/05/photoframe_03.jpg

Once the glue dries, you can apply whatever color you want on the frame.

Notice that my cutting is slightly off, if you have the time and resources to spare then you might want to consider getting it to perfection.

As for the frame, you can also sand it or apply clear coat on it, whichever you deem fit.

http://www.moeness.com/wp-content/uploads/2017/05/photoframe_04.jpg

To have the image in place, I use double-sided tape and applied it to 4 corners of the frame. Make sure there’s sufficient sticky surface to hold the image on the frame.

Once you’re done, you can apply another set of double-sided tape so you could stick it to a wall.

Another means to display the image would be to make a stand for it so it becomes a table-top photo frame.

http://www.moeness.com/wp-content/uploads/2017/05/photoframe_05.jpg

Like this tutorial? Check out the photo PICTURE #1759718

I think the photo frame does make the image more interesting.

Just added another pic that's using this photo frame PICTURE #1760245
1,191 просмотр. • 6 комментариев

Комментарии6 комментариев

0pt
Bayuro (6 месяцев назад) #21307778Nice tutorial but I noticed that you cut the joints very hastily that's why there are some awkward gaps on the corners. I have a tip for you, just make sure you cut the joints for the corners exactly 45 degrees and those awkward gaps will be gone. By the way, craft knife is more practical than scissors in this case.

Yup, rush job. Thanks, it is supposed to be 45. I went with rough estimation but it went really off quite a bit.
6 месяцев назад
0pt
Nice tutorial but I noticed that you cut the joints very hastily that's why there are some awkward gaps on the corners. I have a tip for you, just make sure you cut the joints for the corners exactly 45 degrees and those awkward gaps will be gone. By the way, craft knife is more practical than scissors in this case.
6 месяцев назад
2pt
KiruKiru (6 месяцев назад) #21253047i was plannig todo this when i make a diorama. thanks

Nice, hope this helps. I've been wanting to do this for the longest of time and I finally did it for this pic. :D
6 месяцев назад
0pt
i was plannig todo this when i make a diorama. thanks
6 месяцев назад
0pt
Heldrik (6 месяцев назад) #21246257Nice tutorial of a simple but effective way to add life to a diorama. As they say, it's the little things...

Yup, adding via software works but not always. Gonna have to make more.
6 месяцев назад
1pt
Nice tutorial of a simple but effective way to add life to a diorama. As they say, it's the little things...
6 месяцев назад
Your source for old and rare figurines!

About this blog

 
Welcome to my blog!

More by goldfriesВсе

Связанные предметы 0

Теги0

Связанные клубы 0